IP Camera Set Up
Hi,
Hope this is right place to ask this. Purchased a cheap, no brand IP Camera, but having a nightmare with trying to set up. The IP search software that came with the camera, finds the camera, when attaching to the Superhub2. It is recognised as 192.168.1.10, subnet mask 255.255.255.0 Gateway as 192.168.1.1...and this is where my problems start..I can't get any further. I believe the Gateway should be192.168.0.1, but after changing this, then selecting 'Modify' on in the software, i get 'Set gateway failed'. Could this likely be a fault with the software/camera...or am i misunderstanding the gateway to use ? If i go to the web and try to connect to the webcam on 192.168.1.10 i get page not found...so something certainly isn't right. I'm tearing my hair out....well I would if i had any. It's all the more embarrassing for me as I'm a Software Test Analyst by trade, so work in IT and build my own PCs, so I'm no technophobe!! Any thoughts/ideas are welcomed regards TrevP |
Re: IP Camera Set Up
If its on 192.168.1.0/24 by default give you computer a static ip in that range and browse to it, either set it to DHCP or set it to an IP on your 192.168.0.0/24 network.
|
Re: IP Camera Set Up
Quote:
I don't really want to be messing about changing anything around my PC. I was hoping the camera wouldreally work out of the box as that seems to be the case with other set ups that i have looked at. Frustrating the hell out of me that the camera ip search software that seems to believe the gateway is on 192.168.1.1, rather than 192.168.0.1...and it won't allow me to modify that, even though the instruction guide suggest i should be able to do that. It tells me failed gateway I suppose my my question would be, what could be the issue stopping the softwar allowing me to modify the gateway to 192.168.0.1 Trev |
Re: IP Camera Set Up
Just change the settings to configure the camera onto the right subnet and then change it back. It's not a permanent change.
|
Re: IP Camera Set Up
I don't want to sound too harsh but this is what happens when you buy cheap stuff. Routers (isp supplied or otherwise) are always setup with an ip of 192.168.1.1 (like my Linksys routers) or 192.168.0.1 (as with the shubs). In your case it sounds like a default gateway/subnet has been set in the camera software and although you would expect to be able to change it the fact that you can't leads me to believe that poor development costs have either resulted in them writing the settings into the software which can't be changed or there is a bug in the software which they haven't fixed which won't let you change it.
Either way, the only way round it as Matt said is to change the ip addressing scheme for your network to bring it in line with the settings on the cameras. Your pc shouldn't care to much because all the addresses are going to be managed by the shub. The problem you are going to have is whether the shub lets you do it or not. 3rd party routers will let you change the address completely as well as the subnet mask but the shub's used to be set in concrete. On shub1 you was stuck with 192.168.0.1, I don't know if that has changed now. |
Re: IP Camera Set Up
What make of cheap on camera is it?
|
Re: IP Camera Set Up
Quote:
As i have alluded, i believe it could be that the software has a bug as the instruction manual certainly shows modifying the assigned camera ip address AND the gateway assigned at start up. AS said I'm not a technophobe, I'm a software tester/anayst, but networks are not my cup of tea, so messing with the settings on the router are not where i really want to go. But if I have to, and the SH2 allows me to change stuff, what happens to all the other devices connected to the network,my PC, the wife's laptop and several wireless devices ? Ultimately I want to use the camera wireless and not 'hard wired'. I no doubt will be back here...I'm rather quite embarrassed that I don't know this stuff :( TrevP ---------- Post added at 12:28 ---------- Previous post was at 12:18 ---------- Quote:
---------- Post added at 13:20 ---------- Previous post was at 12:28 ---------- Right. Progress :) I assigned the camera a different ip address on the the gateway that it was defaulting to, and hey presto..it accepted that! Happy days. And now I can see images from the camera on the newly assigned ip address. Now how to set up for wireless access...it will be another minefield for me ! TrevP |
Re: IP Camera Set Up
Just goes to show "so work in IT" means nothing. It's such a wide field.
|
Re: IP Camera Set Up
Quote:
Like I always say, if you want everything to work properly then you need to buy a proper router™ |
All times are GMT +1. The time now is 10:10. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.